|
All values measured to ground unless otherwise noted
|
| Conn./Plug/Pin |
Pin Information |
Test Value |
Comments |
| N7 |
|
|
|
| 1.1 |
Circuit 56b voltage supply output,Left front low beam lamp |
Lights on, S1 in pos II,S4 in low beam pos 12 VDC |
activated from S1 pin 1 via S4 , fused by F1f13 feed to N7 3.2 |
| 1.2 |
Circuit 56a voltage supply output,Left front high beam lamp |
Lights on, S1 in pos II,high beam lights on 12 VDC |
activated from S1 pin 1 via S4 , fused by F1f15 feed to N7 3.1 |
| 1.3 |
Circuit 56b voltage supply output,Right front low beam lamp |
Lights on, S1 in pos II,S4 in low beam pos 12 VDC |
activated from S1 pin 1 via S4 , fused by F1f14 feed to N7 3.4 |
| 1.4 |
Circuit 56a voltage supply output,Right front high beam lamp |
Lights on, S1 in pos II,high beam lights on 12 VDC |
activated from S1 pin 1 via S4 , fused by F1f16 feed to N7 3.3 |
| 1.5 |
pin not used |
|
|
| 1.6 |
Circuit 58N voltage supply output,Left front fog lamp |
Lights on, S1 in pos I or II, S4 in low beam pos.12 VDC with S1 pulled out to pos.1 |
activated from S1 pin 7, feed to N7 3.5 |
| 1.7 |
pin not used |
|
|
| 1.8 |
Circuit 58N voltage supply output,Right front fog lamp |
Lights on, S1 in pos I or II, S4 in low beam pos.12 VDC with S1 pulled out to pos.1 |
same as pin 1.6 |
| 2.1 |
Circuit 54, stop lamp voltage supplyLeft stop lamp |
12 VDC with brakes applied |
activated from S2/1 via S9/1, feed to N7 3.15 |
| 2.2 |
Circuit 58, side marker lamp voltage supplyLeft side marker lamp |
Lights on, S1 in pos I or II, 12 VDC |
Feed from F1f3 |
| 2.3 |
Circuit 54, stop lamp voltage supplyRight stop lamp |
12 VDC with brakes applied |
same as pin 2.1 |
| 2.4 |
Circuit Ke, license plate lamp voltage supplyLeft license plate lamp |
Lights on, S1 in pos I, 12 VDC |
Feed from F1f1 via S1 pin 5,4 to N7 3.16 |
| 2.5 |
Circuit 15, backup lamp voltage supplyLeft backup lamp |
Ignition on,12 VDC with gear shift lever in position "R" |
Feed from F1f6see diagram PE27.19-2000 |
| 2.6 |
Circuit Ke, license plate lamp voltage supplyRight license plate lamp |
Lights on, S1 in pos I, 12 VDC |
same as pin 2.4 |
| 2.7 |
Circuit 15, backup lamp voltage supplyRight backup lamp |
Ignition on,12 VDC with gear shift lever in position "R" |
same as pin 2.5 |
| 2.8 |
Circuit 58, left taillamp voltage supplytail/parking lamp |
Lights on, S1 in pos I or II, 12 VDC |
Feed from S1 pin 10 via F1f3 to N7 3.8 |
| 2.9 |
Circuit 58, side marker lamp voltage supplyRight side marker lamp |
Lights on, S1 in pos I or II, 12 VDC |
Feed from F1f1 |
| 2.10 |
Circuit 58, right taillamp voltage supplytail/parking lamp |
Lights on, S1 in pos I or II, 12 VDC |
Feed from S1 pin 3 via F1f1 to N7 3.6 |
| 3.1 |
Circuit 56a, fused voltage input, Left high beam |
Lights on, S1 in pos II,S4 in high beam pos 12 VDC |
Feed from S1 pin 1 via S4s3 to F1f15 |
| 3.2 |
Circuit 56b, fused voltage input, Left low beam |
Lights on, S1 in pos II,S4 in low beam pos 12 VDC |
Feed from S1 pin 1 via S4s3 to F1f13 |
| 3.3 |
Circuit 56a, fused voltage input, Right high beam |
Lights on, S1 in pos II,S4 in high beam pos 12 VDC |
Feed from S1 pin 1 via S4s3 to F1f16 |
| 3.4 |
Circuit 56b, fused voltage input, Right low beam |
Lights on, S1 in pos II,S4 in low beam pos 12 VDC |
Feed from S1 pin 1 via S4s3 to F1f14 |
| 3.5 |
Circuit 58N, fog lamp fused voltage input |
12 VDC with fog lamps on |
same as pin 1.6 & 1.8 |
| 3.6 |
Circuit 58, right tail/parking lamp fused voltage input |
Lights on, S1 in pos I or II, 12 VDC |
same as pin 2.10 |
| 3.7 |
Main ground to W1 |
Approx. 0 Ohms to ground |
|
| 3.8 |
Circuit 58, left tail/parking lamp fused voltage input |
Lights on, S1 in pos I or II, 12 VDC |
same as pin 2.8 |
| 3.9 |
Circuit 15 fused power input |
Ignition on 12 VDC |
Feed from F1f5 |
| 3.10 |
Exterior lighting failure signal, switched ground |
Approx. 0 Ohms to ground with one or more exterior lighting lamps defective |
Lights A1e14 |
| 3.11 |
pin not used |
|
|
| 3.12 |
Circuit 61e voltage decoupled signal input |
12 VDC with generator running |
Feed from generator via IC |
| 3.13 |
Circuit 15, backup lamp voltage input |
Ignition on,12 VDC with gear shift lever in position "R" |
same as pin 2.5 & 2.7 |
| 3.14 |
Circuit 49a, pulsed turn signal input |
12 VDC intermittent with hazard flasher onIgnition on: 12 VDC intermittent with right or left turn signal on |
Feed from S4/s1 orS6, see diagram PE82.10-2200 |
| 3.15 |
Circuit 54, center high mounted stop lamp voltage supply |
12 VDC with brakes applied |
same as pin 2.1 & 2.3 |
| 3.16 |
Circuit KE, license plate lamp voltage inputAlso lights on recognition signal to other systems (HCS / Lights on warning) |
Lights on, S1 in pos I, 12 VDC |
same as pin 2.4 & 2.6 |