All values measured to ground unless otherwise noted | ||||
N35 | Note 1 | |||
12 | Circuit Ke, license plate lamp voltage outputlights on feedback input from F1f1 | Engine running, S1 in pos. 0 12 VDC | same as N7 pin3.16to S1 pin13generates circuit Ke | |
3 | Circuit 61, engine running signal input, activates "lights on" relays in N35 | Engine running, S1 in pos. 0 12 VDCDaytime running lamps on | see pin5 | |
4 | Circuit 30 main power input | 12 VDC all times | Feed from Terminal block X4 (circuit 30) | |
5 | Circuit 15 relay voltage supply high side,enables "lights on" relays in N35 | Ignition o n 12 VDC | relays are activated by circ. 61 (see pin3) | |
6 | Circuit 50 starter lockout voltage,lights on inhibit signal input | Start engine 12 VDC while starter cranksEngine running <2 VDC | Lights not on Lights on | |
7 | Circuit 56b low beam voltage supply output | Engine running, S1 in pos. 0 12 VDC | low beam lights on | |
8 | pin not used | |||
9 | Main ground to W1 | Approx. 0 Ohms to ground | ||
10 | High beam lights on signal input deactivates low beam relay in N35 | Engine running low beam mode < 2VDCswitch S4 to high beam pos. 12 VDC | ||
1112 | Circuit 58 taillamp voltage supply outputleft taillamp right taillamp | Engine running, S1 in pos. 0 12 VDC | Feed to F1f1Feed to F1f3 | |
N7 | ||||
1.1 | Circuit 56b voltage supply output,Left front low beam lamp | Lights on, S1 in pos II,S4 in low beam pos 12 VDC | activated from S1 pin 1 via S4 , fused by F1f13 feed to N7 3.2 Note 1 | |
1.2 | Circuit 56a voltage supply output,Left front high beam lamp | Lights on, S1 in pos II,high beam lights on 12 VDC | activated from S1 pin 1 via S4 , fused by F1f15 feed to N7 3.1 | |
1.3 | Circuit 56b voltage supply output,Right front low beam lamp | Lights on, S1 in pos II,S4 in low beam pos 12 VDC | activated from S1 pin 1 via S4 , fused by F1f14 feed to N7 3.4 Note 1 | |
1.4 | Circuit 56a voltage supply output,Right front high beam lamp | Lights on, S1 in pos II,high beam lights on 12 VDC | activated from S1 pin 1 via S4 , fused by F1f16 feed to N7 3.3 | |
2.4 | Circuit Ke, license plate lamp voltage supplyLeft license plate lamp | Engine running 12 VDC orLights on, S1 in pos I, 12 VDC | Note 1 | |
2.6 | Circuit Ke, license plate lamp voltage supplyRight license plate lamp | Engine running 12 VDC orLights on, S1 in pos I, 12 VDC | same as pin 2.4 | |
2.8 | Circuit 58, left taillamp voltage supplytail/parking lamp | Engine running 12 VDC orLights on, S1 in pos I or II, 12 VDC | activated from N35 pin 11 via F1f3 to N7 3.8 Note 1 | |
2.10 | Circuit 58, right taillamp voltage supplytail/parking lamp | Engine running 12 VDC orLights on, S1 in pos I or II, 12 VDC | activated from N35 pin 12 via F1f1 to N7 3.6 Note 1 | |
3.1 | Circuit 56a, fused voltage input, Left high beam | Lights on, S1 in pos II,S4 in high beam pos 12 VDC | Feed from S1 pin 1 via S4s2 to F1f15 | |
3.2 | Circuit 56b, fused voltage input, Left low beam | Engine running 12 VDC orLights on, S1 in pos. II, | Feed from either S1 pin1 via S4s3 or N35 pin7 Note 1 | |
3.3 | Circuit 56a, fused voltage input, Right high beam | Lights on, S1 in pos II,S4 in high beam pos 12 VDC | Feed from S1 pin 1 via S4s2 to F1f16 | |
3.4 | Circuit 56b, fused voltage input, Right low beam | Engine running 12 VDC orLights on, S1 in pos. II, | Feed from either S1 pin1 via S4s3 or N35 pin7 Note 1 | |
3.6 | Circuit 58, right tail/parking lamp fused voltage input | Engine running 12 VDC orLights on, S1 in pos. I or II, 12 VDC | same as pin 2.10 | |
3.8 | Circuit 58, left tail/parking lamp fused voltage input | Engine running 12 VDC orLights on, S1 in pos. I or II, 12 VDC | same as pin 2.8 | |
3.16 | Circuit KE, license plate lamp voltage inputAlso lights on recognition signal to other systems (HCS / Lights on warning) | Lights on, S1 in pos I, 12 VDC | same as pin 2.4 & 2.6 | |
Note 1 | daytime running light feature switches on ![]() ![]() ![]() ![]() |
The daytime running light function is canceled by switching on the parking lights or low beam headlamps with exterior light switch S1. | ||
Note 2 | Due to various functions N7 is split up in several system diagrams, therefore only the related pins are listed. Pins not shown are unrelated to this system |